home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Collection of Tools & Utilities
/
Collection of Tools and Utilities.iso
/
dskut
/
525td.zip
/
README.TOO
< prev
next >
Wrap
Text File
|
1992-03-10
|
13KB
|
358 lines
******************************************************
* *
* FileSafe Tape Software Release Version 5.2.3-TD *
* *
******************************************************
ENHANCEMENTS
============
Data Compression
----------------
Data compression during backup typically doubles the useful capacity
of any tape cartridge; those which formerly held 40 megabytes (QIC40) will
now hold 80 megabytes, while those which held 150 megabytes (TD-101 with
an extended length cartridge) may now hold 300 megabytes.
Backup performance typically improves, depending upon hard disk and
CPU speed. QIC40 and QIC80 users (those without a Mach2 card) in
particular will notice increased speed when using compression.
When 5.2.3-TD is first installed, the default is to write all volumes
using data compression. If a user should wish to disable compression,
this can be done via the Utilities, Defaults screen in the lower right
hand corner. Most users will never have a reason to disable this feature.
The actual capacity of each tape can no longer be precisely determined
prior to a backup operation. This is because some files (e.g., data base or
document files) compress very well, while others (e.g., previously ZIPped
or ARCd files) do not compress at all, and may even expand slightly.
Because of the inability to accurately predict tape capacity when
writing compressed volumes, users will occasionally receive warnings
from FileSafe that a given backup will not fit on a particular tape.
When this happens, the user is given the opportunity to format additional
tracks, change tapes, abort the operation, or to simply proceed. Often,
the best choice when writing compressed is to simply proceed; the volume
may in fact fit.
Please see your user's manual and addendums for more details regarding
this powerful new feature.
New Integrated Mach2
--------------------
Supports new Mach2 controller board in "Setboard."
PROBLEM CORRECTIONS
===================
Fixed incompatibilities found using the Mach2 controller on some
386 and 486 systems.
NEW DEFAULT HARDWARE CONFIGURATION
==================================
The Mach2 controller for non-microchannel systems is now being
shipped with jumpers set for DMA channel 3 and interrupt channel 5.
This setting is best for AT-class machines; XT-class systems will
fail CHKTAPE, however, because these settings conflict with the
hard disk controller. If you are installing a Mach2 on an XT, be
sure to change these jumpers first. We recommend using DMA 1 and
interrupt 3 on XTs; alternatively, DMA 2 and interrupt 6 may be
set.
******************************************************
* *
* FileSafe Tape Software Release Version 5.2.2-TD *
* *
******************************************************
PROBLEM CORRECTIONS
===================
Add a patch to support interrupt handling with Phoenix Bios.
******************************************************
* *
* FileSafe Tape Software Release Version 5.2.1-TD *
* *
******************************************************
PROBLEM CORRECTIONS
===================
Occasional Computer Lock-Ups
----------------------------
In prior releases, the TAPE software would cause the computer system to
lock-up and require a power-on reset. This condition would occur during
periods where the tape drive was not streaming, and the TAPE software was
waiting for I/O buffers to be made available. This has been corrected in
this software release.
Mach2 Controller On PS/2
------------------------
On some PS/2 models, such as the Model 70 25MHz, use of the Mach2 controller
may occasionally cause the computer system to hang if the DMA mode is set
to burst mode. If this problem is encountered on a PS/2, it is suggested
that the DMA mode be set (via the reference disk) to Single Transfer for
the Mach2 controller.
KNOWN LIMITATIONS
=================
IBM PS/2 Model 70 25 MHz
------------------------
Installing the TD4000 or 8000 Plus tape drives on this computer
requires using the Mach2 controller board. However, some problems
have been noticed when DMA channels higher than 6 are used for the tape
drive. To avoid these problems, it is suggested that the Fairness mode
be turned off (via the reference disk) for the IBM Fixed Disk Adapter
when using DMA channels higher than 6.
Compaq Deskpro 286 (TM)
-----------------------
The CHKTAPE program automatically configures the TAPE software to run
with the installed hardware. However, on this computer, the software will
incorrectly set the "Controller type" to 5 when using a Mach2 controller
with a an internal 8000 Plus (Part Number 01-30525-01). This will record
QIC-80 format at slow speed.
By entering the Utilities Install screen, the "Controller type" can
be manually set to the desired format. Refer to the on line help for more
information on this option.
If you wish to run at high speed QIC-80 format, the tapes will require
preformatting with the "Controller type" set to 5. After formatting, return
to the Utilities Install screen and change the "Controller type" to the
desired format prior to performing a backup.
With the internal 8000 Plus (Part Number 01-30526-01), you will be
unable to use any "Controller type" besides 7. CHKTAPE will automatically
configure the software to run as type 7.
Novell Users - Directory Naming
-------------------------------
Novell allows creating directories which do not adhere to the DOS
naming limit of 8.3 (as in ACCOUNTI.NG). Novell allows you to create
the same directory as ACCOUNTING which exceed 8 characters. If
such directory names are on the Novell partition when a backup is
performed, an attempt to restore would result in a "Path not found"
error for all data on the tape.
To check for the existence of these directories, use the DOS TREE
command and check for any messages indicating an invalid directory.
Novell Users - Macintosh Interface
----------------------------------
Novell 2.15 operating system allows Macintosh users to store
Macintosh files on the server. This version of the software does
not support Macintosh files and uncertain results will occur if
Macintosh files and directories exist on the server when a backup
or restore is done.
Novell Users - Restoring Rights and Trustee Lists
-------------------------------------------------
Restoring data to a Novell system allows the option of restoring
Novell security information in the form of Novell's Rights and Trustee
Lists (R&TL). If a complete backup is always done, a restore will
always retrieve the R&TL if requested.
Backups using "Backup of modified files by archive bit or since":
If this type of "modified since" backup was used and to ensure all R&TL
are properly restored, you should start by restoring from the last
complete backup answering Yes to "Do you wish to restore the Rights
and Trustee Lists..." prompt, then restore the last modified since
backup, again answering Yes to the prompt for R&TL.
Backup using "Archive attribute backup only":
Start by restoring the last complete backup, then restore IN ORDER
all of the "modified since" backups. In all restores, answer Yes to
the "Do you wish to restore the Rights and Trustee Lists..." prompt.
IMPORTANT CONSIDERATIONS
========================
Backup/Restore Verification
---------------------------
It is highly recommended that a verification pass be made after a backup
or restore operation. This will insure the integrity of the backup or
restore, and can be used as a precaution against corrupted data.
One convenient way to do thi